How To Change Brake Pads on 2004 Honda Accord?

Changing brake pads on your 2004 Honda Accord can be a fairly simple job, provided you have the right tools and know how to do it. 

Make sure you flush out all of the brake fluid before reassembling everything-this will help prevent rusting and also keep your car running smoothly. 

Don’t forget to bleed your brakes properly at least once every three months or when there is an obvious sign of wear or tear on your system. 

This step helps distribute pressure evenly throughout the entire system so it doesn’t fail catastrophically while you’re driving.

Brake Pads on 2004 Honda Accord

Honda Accord 2004 brake pads are made of a high-quality, durable rubber compound that helps to stop the car quickly. 

If your brakes feel spongy or don’t seem to be stopping the car as well as they used to, it may be time for new brake pads on your 2004 Honda Accord. 

The best way to determine if it’s time for new brake pads is by trying them out and seeing how much better the braking feels overall when using them. 

Always replace brake pads according to the manufacturer’s instructions, which usually involve unscrewing the wheel hubcap and taking off the caliper bracket. 

Brake Pads on 2004 Honda Accord

Once you have replaced your2004 Honda Accord brake pads, make sure you clean all of the dust and dirt from underneath and around each rotor before re-installing them into their respective locations on your car’s axle.

Often times missed objects such as stones can get lodged in between rotors causing serious damage so keep an eye out while driving. 

Finally remember never push down too hard with your foot when applying pressure to the pedal because this could cause uneven wear on either pad – resulting in premature replacement.

How To Change Brake Pads on 2004 Honda Accord

Changing brake pads is a simple job that can be done on most cars. The following guide will show you how to do it on a 2004 Honda Accord.

Locate The Brake Pads

The brake pads are located on the inside of your 2004 Honda Accord’s disc brakes. To change them, you’ll need to remove the wheel and tire.

Locate The Brake Pads

Remove The Brake Pedal Pad Retainer Clip

To get to the brake pedal pad, you’ll first have to remove the retaining clip from the front of the brake pedal pad assembly. Pry it off with a small screwdriver or needle-nose pliers.

Remove The Brake Pedal Pad Retainer Clip

Disconnect The Brake Line from The Wheel Cylinder

Once you’ve removed the retaining clip, disconnect both ends of the brake line from either side of your car’s wheel cylinder using a wrench or an axle nut tool (depending on which side your booster is). 

Don’t lose these clips. You can reinstall them after replacing your pads by reversing these steps: thread one end of each clip onto its respective connection point; then twist it slightly until it snaps into place.)

Disconnect The Brake Line from The Wheel Cylinder

Slide Off Old Pad(s) And Replace with New Ones

Once you’ve disconnected and replaced both ends of your brake line, slide off old pads and install new ones in their place – just like that. 

Remember to torque down all four mounting screws once the installation is complete.

Slide Off Old Pad(s) And Replace with New Ones

Reinstall Wheel and Tire After Replacing Pads

After replacing brake pads, it is important to reinstall the wheel and tire. This will ensure that your car has a solid foundation from which to work and prevents any further damage from happening.

When to Change Brake Pads on 2004 Honda Accord

If you see any of the following signs that say your brake pads need to be replaced, it’s time to do so:

Brake Pads Are Squealing

If the brake pads are squealing, this means that they are not gripping the rotors on your car properly. When this happens, you will have to apply more pressure to the pedal in order to stop your vehicle.

Lots Of Noise Coming from The Brakes

This noise is usually caused by either worn or damaged brake pads. When these pads wear down, they create a lot of friction which results in a lot of noise when you try and stop your car using the brakes.

Can’t Stop on A Straightaway Without Hesitating

The stopping power of your brakes can be affected if there is excessive wear on their components such as the discs or pad springs. 

If these parts start to fail, it may result in difficulty braking quickly and without hesitation on straightaways.

Vehicle Feels Sluggish After Stopping Quickly

When you use your brakes hard, there is a chance that they will heat up quickly which can cause sluggishness afterward as well as decreased fuel efficiency over time due to an increase in emissions from your engine.

Loud Bang

Hard A problem with one or more of your brake lines may lead to loud bangs whenever you apply them forcefully causing vibration throughout the car. 

This issue often occurs after major accidents where cars tend to get towed away and forced into extreme stops suddenly.

FAQs

How Much Do Brakes Cost for a 2004 Honda Accord? 

Honda Accord 2004 brakes can range in price from $27.99 to $213.53.

How Much Does a Honda Brake Job Cost?

Honda brake jobs typically cost between $150 and $450 per axle, depending on the severity of the problem.

How Long Should Honda Accord Brake Pads Last?

The lifespan of a Honda Accord brake pad is typically between 30,000 and 70,000 miles.

Do I Need New Brake Pads with New Rotors?

If your brake pads and rotors are still in good condition, then you don’t need to buy new ones.

How To Change Brake Pads on a 2012 Dodge Avenger

If you need to replace your brake pads on a 2012 Dodge Avenger, follow these steps: 

  1. Remove the wheel. 
  2. Remove the brake caliper. 
  3. Remove the brake rotor. 
  4. Remove the old brake pads. 
  5. Install the new brake pads.

To Recap

If you are having trouble with your 2004 Honda Accord’s brake pads, follow these simple steps: Remove the screws that hold on the caliper brackets.

Grip the top of each bracket and pull it off Lift up on each side of the rotor to remove it from its caliper Inspect each pad for wear or damage Replace any worn or damaged pads. 

Align new rotor and brackets onto car chassis, replace screws, and grip tops of brackets while tightening them in place using a screwdriver.

Do not over-tighten as this can cause distortion in metal parts surrounding rotor (you may need to use a wrench if needed) – reattach wheel guards if applicable before driving away.

Leave a Comment