How To Change Brake Pads on Toyota 4RUNNER?

Brake pads are an important safety feature on any vehicle, and they need to be replaced regularly according to the manufacturer’s guidelines. If you’re not sure how to change brake pads yourself, a mechanic can do it for you in a relatively short amount of time. 

You’ll need some basic tools and supplies, including a jack and lug wrench. There are specific steps that must be followed in order to replace brake pads successfully; follow the manufacturer’s instructions carefully. 

It’s always important to have your car inspected by a professional before making any major repairs or changes – this includes changing your brake pads.

Toyota 4RUNNER Brake Rotors

Brake pads are the part of the brake system that stops the car. They are made up of a metal plate with friction material on it. The friction material is usually made up of a mixture of carbon and ceramic particles.

The brake pads on Toyota 4RUNNER are located in the front and rear wheels. 

Toyota 4RUNNER Brake Rotors

The brake pads can be changed by removing them from their mounting points, then sliding them out from between the rotor and hub assembly, then sliding them back into place.

How To Change Brake Pads on Toyota 4RUNNER

If you need to change your brake pads on a Toyota 4Runner, follow these easy steps.

In this guide, we will show you how to change brake pads on a Toyota 4Runner. This is a fairly common repair that can be done with just a few tools and some basic knowledge of automotive mechanics.

Remove the wheel

To remove the brake pads, you first need to remove the wheel. This can be done by disconnecting the battery cable and removing the screws that hold it in place.

Remove the wheel

Disconnect the battery cable

Next, you’ll need to disconnect the battery cables from both sides of the car. This will allow you to access and replace your brake pads without affecting any other electrical components in your Toyota 4Runner.

Disconnect the battery cable

Locate and release brake pedal disk cover

Finally, on each side of your 4Runner, locate and lift off the brake pedal disk cover (shown below). Make sure not to lose any of these parts.

Lift Up on Each Side of the Brake Pads

To change brake pads, you will first need to remove them from their holders. This can be done by lifting up each side of the pad and then pulling it out of its holder.

Lift Up on Each Side of the Brake Pads

Remove Them from Their Holders

Once you have removed the brake pads, you will need to remove them from their holders. To do this, simply pull them out of their respective holders. Make sure that they are fully detached before moving on to step 3 below.

Remove Them from Their Holders

Place Them on The Discs

Now that the brakes are free from their holders, it is time to place them onto the discs. To do this, align the edge of one brake pad with the center line on your disc and press down until it locks into place. 

Do not over-tighten these bolts as this could damage your disc or cause other problems down the road.

Install The Bolts and Washers

Finally, install any necessary bolts and washers (if applicable). Be sure to tighten these screws in a clockwise direction by hand.

Install The Bolts and Washers

Signs of Bad Rotors That Need to Be Replaced

If you notice any of the following signs that your brake pads need to be replaced, it is time to take action:

Vehicle Won’t Start

If your brake pads are worn down to the metal, your vehicle may not start. This is because when the rotor becomes too thin, it will no longer be able to stop the car from rolling. 

This can cause a number of problems including decreased braking performance and an increased risk of getting into an accident.

Poor Stopping Power

When your brake pads are worn down to the metal, they won’t provide as much stopping power as they used to do. As a result, you may have to apply more pressure in order to stop your car – which could lead to an increase in accidents or traffic jams.

Bad Braking Behavior

If you notice that your brakes aren’t working as well as they used to – for example, if they seem sluggish or don’t always work properly – this might be due to bad rotors that need replacing. 

If left untreated, these rotors could eventually wear away completely and render your brakes unusable altogether. But the best rotors will serve you for a long time.

Increased Risk of Getting into An Accident

If you have poor braking performance coupled with weak stopping power – two factors that often go hand-in-hand – then there is a greater chance of getting into an accident than usual on busy roads or highways.

FAQs

How Much Does It Cost to Replace Brakes on a Toyota 4RUNNER?

Toyota 4Runner brake pads replacement can cost anywhere between $150 and $300 per axle depending on the type of brakes.

Can I Change My Brake Pads Myself?

The process of replacing brake pads is not difficult, but it can be dangerous if you don’t know what you’re doing. If you’re not sure about how to replace your brake pads, it’s best to take your car in for service or call a professional mechanic.

Can You Change Front Brake Pads Yourself?

If you want to replace the brake pads in your car’s disc brake system quickly and easily, you can do so with a few simple steps.

Should I Replace My Front or Rear Brakes First?

The front brakes are more likely to wear out first, so it is best to replace them first. The rear brakes will last longer than the front brakes, but they will still need to be replaced eventually.

Why Do Front Brakes Wear Faster?

Front brakes in particular are tasked with stopping the car from crashing into other vehicles. 

They must be able to withstand more pressure and heat than other brakes, working quickly and efficiently to stop the vehicle from moving too fast.

What Is the Life Expectancy of Rotors?

The life expectancy of rotors is 30000 to 70000 miles based on their size and how often they’re used.

Should I Replace All 4 Rotors?

Replacing the four rotors on your car with an aftermarket part will not only save you time and money, but it can also extend the life of the vehicle.

To Recap

Changing brake pads is an important task to keep your Toyota 4Runner running smoothly and safely. 

The right tools are necessary for the job, so be sure to have them before starting. Follow these simple steps to change the pads: 

Be careful when removing and replacing the brake pads; don’t damage any of the components or you’ll have to replace them all. 

After changing the brakes, make sure that everything functions as it should by trying out each function on your car one last time before leaving for good measure.

 With that in mind, you need to know how to perform basic maintenance on your car’s brake pads.

Leave a Comment