How to Change Rear Brake Pads on Polaris Ranger?

Changing brake pads on your Polaris Ranger is an easy task that can be completed in a few hours by following the proper steps. 

The rear pads are located behind the front wheels and need to be replaced when they start to wear down or if there is damage from debris or accidents. 

There are two types of brake pads, friction and anti-lock, which you will want to decide on depending on the type of riding that you do most often. 

You will also need new fluid for the brakes, so make sure to have this on hand before beginning the installation process.

Rear Brake Pads on Polaris Ranger

Rear brake pads are a crucial part of your Polaris Ranger’s safety arsenal, so it is important to choose the right ones for your vehicle. When you replace your rear brake pads, always make sure that you use the correct type and size pad for your motorcycle. 

Make sure that you have enough time to remove and install the new brakes properly before hitting the road. The best way to find out if your rear brake pads need replacement is by checking them regularly with a caliper or roto meter tool. 

Replace all four rear brake pads on most Polaris Rangers every 60,000 miles or six years, whichever comes first. 

Rear Brake Pads on Polaris Ranger

If one of the pistons in your master cylinder wears down too much over time (a common problem), then it will affect braking performance as well as wear on other components in the system like wheel cylinders and seals.

How to Change Rear Brake Pads on Polaris Ranger

If you’re having trouble stopping your Polaris Ranger from rolling, it may be time to replace the rear brake pads. If your Polaris Ranger is experiencing brake problems, you’ll likely need to replace the rear pads. 

This can be done with a few simple tools and requires only basic knowledge about car mechanics.

How to Change Rear Brake Pads on Polaris Ranger

Changing brake pads is a common job for many drivers and can be done on most cars. The steps in this guide will show you how to do it on your Polaris Ranger.

Disconnect the battery cables

Before you start, disconnect any external power sources that may be attached to the vehicle (like a trailer hitch). This will ensure that you have enough room to work and avoid any potential accidents.

Disconnect the battery cables

Remove the rear wheel

Remove the rear wheel by unscrewing it from the axle. Make sure to keep track of which brake pad goes on which side.

Remove the rear wheel

Unbolt and remove the old brake pads

After tightening all of the bolts in place, it is now time to remove the old brake pads by unscrewing them from their mounting bracket.

On each side, locate two bolts that hold in the brake pads (one at each end). Once these are removed, carefully pull them away from your vehicle’s braking system. Be careful not to damage anything while removing them.

remove the old brake pads

Once everything has been assembled and ready, apply pressure with your hands against each pad until it pops off easily from its mounting bracket. Clean up any residue left over from removal with a cloth before replacing the pad onto its mounting bracket.

Inspect and clean if necessary

If there is dirt or debris on your brakes, use a vacuum cleaner or brush attachment to get it off completely before reinstalling your new pads.

If cleaning isn’t an option, replace your brake pads as needed regardless – they can only last for around six months per set so don’t waste time if they need replacing soon.

Reinstall New brake pads

Align both sides of each pad correctly with their corresponding bolt holes and secure with screws provided. 

Be sure to tighten these bolts firmly until they are snug against the rotor surface – this will prevent excessive wear over time.

Reinstall New brake pads

Why You Need to Change Rear Brake Pads on Polaris Ranger

If you’re driving your Polaris Ranger and notice that the brakes are not working as well as they used to, it’s time to change the pads on the rear wheel. 

The brake pads wear down over time and need to be replaced in order for your vehicle to stop safely.

The Vehicle Is Slipping or Poor Stopping Power

A worn brake pad will cause your Polaris Ranger to have less stopping power and can lead to slipping or poor braking performance. A brake pad is a piece of metal that sits on the rotor inside the calipers, and it helps to stop your vehicle. 

When the pads start to wear down, they may become brittle and this can result in them breaking when you try to stop your car.

Brake Pads Making Noise

If you are experiencing noise when you apply the brakes, chances are that there is a problem with your brake pads. 

This noise can come from either the pedal itself or from the rotors hitting against each other as you try to apply pressure on them. In some cases, these problems may also be accompanied by vibrations which make it difficult for you to drive safely.

Your Vehicle Will Lose Acceleration While Driving

When your brakes start wearing down, they may not be able to provide enough resistance when applied suddenly which will cause your vehicle’s engine RPM (revolutions per minute) to drop temporarily-this is commonly called “braking fade”. 

This loss of acceleration can make it difficult for you to get ahead in traffic or go up hills quickly.

Brake Pads Wear Out Over Time and Need to Be Replaced

Brake pads are designed to stop the car from skidding or spinning when you brake. Over time, brake pads can wear down and eventually need to be replaced. This will cause your vehicle to have a harder time braking and may lead to dangerous driving conditions.

Caring Tips on Rear Brake Pads on Polaris Ranger

If you’re experiencing a lot of vibration or squeaking when you brake, it may be time to replace the rear pads on your Polaris Ranger. These pads work with the rotors to stop the car from skidding and making noise. 

Here are some common maintenance tips on Polaris Ranger rear brakes that can help keep your brakes in good condition and prevent any further problems down the line:

Inspect Brake Pads

It is important to inspect your brake pads regularly and replace them when they start to wear down. This will help ensure that you have optimal braking performance and a longer lifespan for your rear brakes.

Rotate Brake Pad Drums

Drums of the brake pads should be rotated every 2000 miles or every three months, whichever comes first. Doing this will optimize pad contact with the rotors and improve overall braking power and durability.

Check Rear Drum Dryness

Make sure that the rear drum is completely dry before applying any type of lubrication; excess moisture can cause corrosion and decrease stopping power on your Polaris Ranger’s rear discs

FAQs

Where Is Polaris Ranger Parking Brake?

Polaris Ranger’s parking brake is located on the rear of the vehicle.

Is There an E Brake on Polaris Ranger?

The Pre-2007 Polaris Ranger has an E-brake with a foot pedal-operated pull handle.

What are car rotors made of?

Generally car rotors are made of ceramic and carbon fiber and so many other things.

To Recap

Brakes are a vital component of your vehicle that must be serviced regularly if you want them to perform at their best. 

If you’re having problems with your Polaris Ranger’s rear brake pads, changing them might be the answer. Changing the pads will fix the most common issues and keep your vehicle safe.

Changing rear brake pads on a Polaris Ranger is an easy task that can be done by anyone with some basic tools and knowledge. 

Follow the instructions provided in this article for changing your brake pads, and you should have no trouble completing the job yourself.

Leave a Comment