How To Replace Rear Brake Pads on Toyota Corolla 2015?

You will need to remove the rear wheel well cover in order to replace your brake pads on a Toyota Corolla 2015. There are four screws that hold the well cover in place, and two of them are hidden behind trim pieces near the front bumper fascia. 

Once you have removed these trim pieces, use a Phillips screwdriver to unscrew the three screws that secure the brake pad holder panel in place. 

Then pull out the old pads and install new ones by reversing these steps. Finally, reinstall all of the trim pieces and attach them with screws if necessary before re-covering your car’s wheel well with its cover.

Tools Required to Change the Rear Brake Pads of Toyota Corolla 2015

This is a guide for Toyota Corolla 2015 rear brake pads change.

Tools Required to Change the Rear Brake Pads of Toyota Corolla 2015:

Tools Required to Change the Rear Brake Pads of Toyota Corolla 2015
  1. Torque wrench       
  2. Ratchet wrench (5/16 inch)
  3. Socket wrench (5/16 inch)
  4. Socket wrench extension bar (6 inches)
  5. Torque screwdriver with a 5/16 inch socket and a 1/4 inch socket
  6. Pry bar with a 5/16 inch blade or flathead screwdriver

Rear Brake Pads for Toyota Corolla 2015

If your car is having problems stopping in a timely manner, it might be time to replace the rear brake pads. 

To do this, you’ll need some tools and knowledge of your Toyota Corolla’s interior. Here are the specific items you’ll need:

Caliper Holders

To change the rear brake pads on a Toyota Corolla 2015, you will need to use caliper holders. These holders fit onto the calipers and hold them in place while you remove and replace the pads.

Caliper Holders

Car Jack

You will also need a car jack to help lift the vehicle off of its wheels so that you can work on it.

Car Jack

Jack Stands

You’ll also need some jack stands to support the weight of your car when changing the brakes.

Jack Stands

Impact Wrench with Ear Mufflers

You’ll need an impact wrench with ear mufflers to replace the rear brake pads on a Toyota Corolla 2015.

Socket Wrench With 14 MM Socket

You’ll also need a socket wrench with a 14 mm socket to remove and install the lug nut on the axle of the car.

Torque Wrench

You’ll need a torque wrench to tighten or loosen various bolts and screws in order that your brake pad replacement goes smoothly.

Brake Cleaner Spray

To clean and lubricate the brake pads, you will need a brake cleaner spray. This type of spray is designed to dissolve dirt and grime from the surface of the brakes.

Anti-seize Lubricant

In order to prevent corrosion on the braking system, it is important to use an anti-seize lubricant. 

This type of lubricant can help stop metal from bonding together and forming rust prematurely

How To Replace Rear Brake Pads on Toyota Corolla 2015

If you’re looking to replace your rear brake pads on a Toyota Corolla 2015, there are a few things that you’ll need before getting started. 

Replace Rear Brake Pads on Toyota

The first thing is to remove the wheel and tire.

Next, disconnect the cables from the brakes at each corner. 

Finally, remove the screws that hold in the pads.

Locate the Rear Brake Pads

Start by locating the brake pads on your Toyota Corolla 2015. The brake pads will be located at the rear of your vehicle.

Locate the Rear Brake Pads

Remove Brake Pad retaining Rings

Once you have located the brake pads, it is time to remove the retention rings from them. These rings keep the brake pad in place and should be removed before replacing the pad. 

Remove Brake Pad retaining Rings

On some models, a tool may be needed to remove these rings.

Disassemble Brake Pedal Assembly

Now that you have removed the retention ring and replaced it with a new one, it’s time to take apart your pedal assembly. This will allow you to replace any broken parts of the rotor as well as adjust any worn ones.

Disassemble Brake Pedal Assembly

Install New Brake Pedal Assembly

After disassembling and reassembling your pedal assembly, slide it into place on top of the rotor and tighten down all of its bolts using a wrench or socket (depending on which model car you are working on). 

Install New Brake Pedal Assembly

Finally, reinstall your parking brakes if they were previously disengaged while doing this repair.

FAQs

Can I Change My Own Rear Brake Pads?

You can change your own rear brake pads if you are comfortable with the process.

If you are not comfortable with the process or think it is too complicated for you, then a mechanic or a professional service shop should do it for you.

Do Toyota Corollas Have Rear Brakes?

Yes, they do have rear brakes.

How Long Do Rear Brakes Last on Toyota Corolla?

The rear brakes on a Toyota Corolla last for about 60,000 miles before they need to be replaced.

How Much Does Toyota Charge for Rear Brakes?

Toyota charges $760.00 for the parts and labor to replace the rear brakes on a Camry.

How Long Do Toyota Rear Brake Pads Last?

The average lifespan for most Toyota rear brake pads is about 40,000 miles.

What to Do with Old Brake Rotors?

You may be able to sell the old brake rotors or give them away to someone who needs them. 

You can also recycle them if they’re in good condition and meet the required standards for recycling. 

Is It Worth Changing Your Own Brakes?

Changing your brakes is not worth it if you don’t know what you’re doing because it’s very easy to get them wrong and end up with worse braking than before.

It is best to go to a professional who can handle this for you.

Can I Just Replace Brake Pads and Not Rotors?

If you want to replace only one or both of these parts, you need to make sure that they are compatible with each other.

How Long Does a Brake Pad Replacement Take?

The average brake pad replacement takes about 20 minutes. It can vary depending on the type of car and its make and model.

To Recap

If your rear brake pads of Toyota Corolla 2015 are worn down to the metal, it’s time to replace them. The process is simple and can be done in just a few minutes using a screwdriver.

Make sure to have the correct size pad for your vehicle before starting, and take care not to pinch or damage any wires during installation.

Leave a Comment